Skip to main content
Ch.11 - Liquids, Solids & Intermolecular Forces
Tro - Chemistry: A Molecular Approach 4th Edition
Tro4th EditionChemistry: A Molecular ApproachISBN: 9780134112831당신이 사용하는 게 아니라요?교과서 변경
모든 교과서Tro 4th EditionCh.11 - Liquids, Solids & Intermolecular Forces문제 95
11장, 문제 95

Based on the phase diagram of CO2 shown in Figure 11.39(b), describe the state changes that occur when the temperature of CO2 is increased from 190 K to 350 K at a constant pressure of (b) 5.1 atm, (c) 10 atm, and (d) 100 atm.

검증된 단계별 안내
1
Step 1: Understand the phase diagram of CO2. A phase diagram shows the state of a substance (solid, liquid, gas) at various temperatures and pressures. Key points include the triple point, critical point, and the lines separating different phases.
Step 2: For (b) 5.1 atm: Locate 5.1 atm on the pressure axis of the phase diagram. At 190 K, CO2 is likely in the solid phase. As temperature increases, observe the path on the diagram to determine when CO2 transitions from solid to gas (sublimation) since 5.1 atm is below the triple point pressure.
Step 3: For (c) 10 atm: Locate 10 atm on the pressure axis. At 190 K, CO2 is in the solid phase. As temperature increases, CO2 will first transition from solid to liquid (melting) and then from liquid to gas (vaporization) as it crosses the phase boundaries.
Step 4: For (d) 100 atm: Locate 100 atm on the pressure axis. At 190 K, CO2 is in the solid phase. As temperature increases, CO2 will transition from solid to liquid (melting) and then from liquid to gas (vaporization) as it crosses the phase boundaries.
Step 5: Summarize the state changes: At 5.1 atm, CO2 sublimes from solid to gas. At 10 atm, CO2 melts from solid to liquid and then vaporizes to gas. At 100 atm, CO2 also melts from solid to liquid and then vaporizes to gas.>

주요 개념

질문에 올바르게 답하기 위해 반드시 이해해야 하는 핵심 개념들은 다음과 같습니다.

Phase Diagram

A phase diagram is a graphical representation that shows the states of a substance (solid, liquid, gas) at various temperatures and pressures. It helps visualize the conditions under which a substance exists in different phases and the transitions between these phases, such as melting, boiling, and sublimation.
추천 영상:
가이드 코스
03:22
Phase Changes in Diagrams

Critical Point

The critical point on a phase diagram marks the end of the liquid-gas phase boundary, beyond which the distinction between liquid and gas phases disappears. Above this temperature and pressure, the substance exists as a supercritical fluid, exhibiting properties of both liquids and gases, which is crucial for understanding behavior at high pressures.
추천 영상:
가이드 코스
03:05
Boiling Point Elevation

Sublimation and Deposition

Sublimation is the process where a solid transitions directly to a gas without passing through the liquid phase, while deposition is the reverse process. For CO2, these phase changes are significant at low temperatures and pressures, and understanding these processes is essential when analyzing state changes as temperature increases in the given pressure conditions.
추천 영상:
가이드 코스
01:52
Sublimation Phase Change Example
관련 실천
교과서 질문

Based on the phase diagram of CO2 shown in Figure 11.39(b), describe the state changes that occur when the temperature of CO2 is increased from 190 K to 350 K at a constant pressure of (a) 1 atm

1632
views
교과서 질문

A sealed flask contains 0.55 g of water at 28 °C. The vapor pressure of water at this temperature is 28.35 mmHg. What is the minimum volume of the flask in order that no liquid water be present in the flask?

1268
views
교과서 질문

Air conditioners not only cool air, but dry it as well. A room in a home measures 6.0 m × 10.0 m × 2.2 m. If the outdoor temperature is 30 °C and the partial pressure of water in the air is 85% of the vapor pressure of water at this temperature, what mass of water must be removed from the air each time the volume of air in the room is cycled through the air conditioner? (Assume that all of the water must be removed from the air.) The vapor pressure for water at 30 °C is 31.8 torr.

997
views
3
rank