Q: During the experiment, you are asked to calculate the percent difference between two measured accelerations $$a_1$$ and $$a_2. $$Which formula should you use?

$$\frac{|a_1$ - a_2$|}{\frac{1}{2}(a_1$ + a_2$)} \times 100\%$$

Question 1

When measuring the position of the air track cart at regular time intervals, why is it important to always record the position from the same end of the track?

Accepted Answer

To maintain consistency in position measurements, which is necessary for accurate calculation of displacement and velocity.

Question 2

Suppose you release the cart from rest at the top of the inclined air track and record its position every second. Which kinematic equation best describes the cart's motion, assuming constant acceleration and initial velocity $$v_0 = 0$?

Accepted Answer

$$x = x_0$ + v_0$ t + \frac{1}{2} a t^2$

Question 3

If the cart is given a single tap at the bottom of the track so that it moves up the incline and then comes back down, what is the expected sign of the acceleration during its upward motion (assuming up the incline is positive)?

Accepted Answer

Negative, because gravity is acting down the incline, opposite to the direction of motion.

Question 4

You are asked to calculate the average velocity of the cart over each time interval using the formula $$v = \frac{\Delta x}{\Delta t}. If $$your position data is in centimeters and your time data is in seconds, what units will your average velocity have?

Accepted Answer

cm/s

Question 5

In the experiment, you are instructed to plot $$v$$ versus $$t$$ and fit a straight line to the data. What does the slope of this line represent?

Accepted Answer

The acceleration of the cart.

Question 6

If you find that the acceleration calculated for the cart going up the incline ($$a_1) is $$significantly different from the acceleration going down ($$a_2$$), what is the most likely source of error?

Accepted Answer

Friction or air resistance affected the cart differently in each direction.

Question 7

Why is it important to use the same time intervals when calculating average velocities and accelerations from your data?

Accepted Answer

It allows for direct comparison between different segments of the motion.

Question 8

Suppose you plot position $$x$$ versus time $$t$$ for the cart and obtain a curve. What does the shape of this curve indicate about the cart's motion?

Accepted Answer

A straight line indicates constant velocity; a curve indicates constant acceleration.

Question 9

If the air track is not perfectly level, how would this affect your measurements of acceleration?

Accepted Answer

It could introduce a systematic error, causing the measured acceleration to be larger or smaller than the true value.

Question 10

During the experiment, you are asked to calculate the percent difference between two measured accelerations $$a_1$$ and $$a_2. $$Which formula should you use?

Accepted Answer

$$\frac{|a_1$ - a_2$|}{\frac{1}{2}(a_1$ + a_2$)} 	imes 100\%$$

Question 11

If you use LoggerPro to plot $$x$$ versus $$t$$ and fit a quadratic curve, which parameter in the fit corresponds to the acceleration of the cart?

Accepted Answer

The coefficient of the $$t^2$$ term, which is $$\frac{1}{2}a.$$

Question 12

A student finds that the velocity of the cart is not zero at $$t = 0$$ when the cart is released from rest. What is the most likely explanation?

Accepted Answer

The cart was not actually at rest when timing started.

Question 13

If you want to minimize friction in your experiment, which of the following should you do?

Accepted Answer

Ensure the air track is properly leveled and the air supply is sufficient.

Question 14

When calculating the average velocity for each time interval, why is it important to use the difference in position ($$\Delta x) $$and time ($$\Delta t) $$between two consecutive measurements?

Accepted Answer

Because it gives the instantaneous velocity at the midpoint of the interval.

Question 15

If the cart is moving up the incline and slowing down, what can you say about the direction of its velocity and acceleration?

Accepted Answer

Velocity is upward, acceleration is downward.

Question 16

Suppose you accidentally record the position of the cart from the wrong end of the track for some measurements. How will this affect your calculated velocities?

Accepted Answer

It will reverse the sign of the velocities for those intervals.

Question 17

Why is it important to start the position measurements at $$x = 0 cm $$for each run?

Accepted Answer

To simplify calculations and allow for direct comparison between different runs.

Question 18

If your graph of $$v$$ versus $$t$$ for the cart going up the incline has a negative slope, what does this indicate about the acceleration?

Accepted Answer

The acceleration is negative.

Question 19

In the analysis, you are told to ignore the y-intercept of the $$v$$ versus $$t$$ graph for the cart going up the incline. Why?

Accepted Answer

Because it represents the initial velocity, which is not important for calculating acceleration.

Question 20

If you observe that the percent difference between $$a_1$$ and $$a_2 is $$very large, what should you do?

Accepted Answer

Check for systematic errors such as friction, misreading the scale, or inconsistent timing.

Motion on an Inclined Air Track: Measurement and Analysis

Guida di studio - Domande di pratica

Study guide - Flashcard