Q: A bridge cable is designed to withstand a maximum normal stress of $$400\ \mathrm{MPa}. If $$the maximum load is $$80,000\ \mathrm{N}$$, what is the minimum cross-sectional area $$A$$ required for the cable?

$$A = 2.0 \times 10$$^{-4}$$\ \mathrm{m}^2$$

Q: A bolt is subjected to a shear force of $$10,000\ \mathrm{N}$$ across an area of $$2.0\ \mathrm{cm}^2. $$What is the shear stress $$\tau on $$the bolt?

$$\tau = 5.0 \times 10$$^{6}$$\ \mathrm{Pa}$$

Q: A steel bar with a cross-sectional area of $$5.0\ \mathrm{cm}^2 is $$subjected to a tensile force of $$25,000\ \mathrm{N}. $$What is the normal stress $$\sigma in $$the bar?

$$\sigma = 5.0 \times 10$$^{6}$$\ \mathrm{Pa}$$

Question 1

A steel rod with an original length of $$2.0\ \mathrm{m} is $$subjected to a tensile force that causes it to stretch by $$1.0\ \mathrm{mm}. $$What is the normal strain $$\varepsilon in $$the rod?

Accepted Answer

$$\varepsilon = 0.0005$$

Question 2

Which of the following best describes the difference between internal and external forces in a loaded beam?

Accepted Answer

Internal forces resist the external loads and occur within the material, while external forces are applied from outside sources such as gravity or a person pushing.

Question 3

A rectangular block is subjected to a shear force causing a deformation angle $$	heta of$$ $$0.01$$ radians. What is the shear strain $$\gamma$$?

Accepted Answer

$$\gamma = 0.01$$

Question 4

A bridge cable is designed to withstand a maximum normal stress of $$400\ \mathrm{MPa}. If $$the maximum load is $$80,000\ \mathrm{N}$$, what is the minimum cross-sectional area $$A$$ required for the cable?

Accepted Answer

$$A = 2.0 	imes 10$$^{-4}$$\ \mathrm{m}^2$$

Question 5

Which statement about the stress-strain curve for materials is correct?

Accepted Answer

The linear region of the stress-strain curve represents elastic behavior, where the material returns to its original shape after the load is removed.

Question 6

A bolt is subjected to a shear force of $$10,000\ \mathrm{N}$$ across an area of $$2.0\ \mathrm{cm}^2. $$What is the shear stress $$	au on $$the bolt?

Accepted Answer

$$	au = 5.0 	imes 10$$^{6}$$\ \mathrm{Pa}$$

Question 7

A material sample is loaded in compression and shortens by $$0.2\ \mathrm{mm}$$ from its original length of $$100\ \mathrm{mm}. $$What is the normal strain $$\varepsilon$$?

Accepted Answer

$$\varepsilon = -0.002$$

Question 8

Which of the following is NOT a type of load that can act on a structure?

Accepted Answer

Expansion

Question 9

A steel wire has a Young's modulus $$E$$ much greater than that of rubber. What does this imply about the wire compared to rubber?

Accepted Answer

The steel wire is stiffer and deforms less under the same load.

Question 10

A brittle material is loaded in tension. What is most likely to happen as it reaches its ultimate strength?

Accepted Answer

It will snap suddenly with little or no plastic deformation.

Question 11

A cylindrical rod is subjected to a compressive force. Which of the following statements is true about the sign of normal strain $$\varepsilon$$?

Accepted Answer

$$\varepsilon is $$negative because the rod shortens.

Question 12

A beam in a building is subjected to bending. Which of the following best describes the resulting deformation?

Accepted Answer

The beam develops curvature, with one side in tension and the other in compression.

Question 13

A steel bar with a cross-sectional area of $$5.0\ \mathrm{cm}^2 is $$subjected to a tensile force of $$25,000\ \mathrm{N}. $$What is the normal stress $$\sigma in $$the bar?

Accepted Answer

$$\sigma = 5.0 	imes 10$$^{6}$$\ \mathrm{Pa}$$

Question 14

Which of the following best describes the meaning of 'dimensionless' when referring to strain?

Accepted Answer

Strain has no units because it is a ratio of lengths.

Question 15

A bolt in a car's suspension is designed to resist shear. Which equation should be used to calculate the shear stress $$	au in $$the bolt?

Accepted Answer

$$	au = \dfrac{V}{A}$$

Question 16

A material is loaded beyond its elastic limit. What happens to the material when the load is removed?

Accepted Answer

It undergoes permanent deformation and does not return to its original shape.

Question 17

Which of the following is a real-world example of shear stress?

Accepted Answer

Cutting paper with scissors.

Question 18

A rod is twisted by applying a torque. What type of load is this?

Accepted Answer

Torsion

Question 19

Which of the following statements about Hooke's Law is correct?

Accepted Answer

Hooke's Law applies only in the elastic region of the stress-strain curve.

Question 20

A steel cable in a suspension bridge is designed to have a maximum strain of $$0.002$$ before permanent deformation. If the original length is $$100\ \mathrm{m}$$, what is the maximum allowable elongation $$\Delta L$$?

Accepted Answer

$$\Delta L = 0.2\ \mathrm{m}$$

Mechanics of Materials: Stress, Strain, and Deformation

Guida di studio - Domande di pratica

Study guide - Flashcard