Skip to main content
뒤로

Chem 2A Exam 3 Study Guide: Chapters 9–13 (Electrons, Bonding, Gases, Intermolecular Forces, Solutions)

스터디 가이드 - 스마트 노트

자료에 맞춘 맞춤형 노트, 핵심 정의, 예시, 맥락을 확장해 제공합니다.

Chapter 9: Electrons in Atoms and the Periodic Table

Energy, Wavelength, and Frequency

The energy of electromagnetic radiation is directly related to its frequency and inversely related to its wavelength.

  • Energy (E): The capacity to do work or produce heat, measured in joules (J).

  • Wavelength (\( \lambda \)): The distance between two consecutive peaks of a wave, measured in meters (m).

  • Frequency (\( \nu \)): The number of wave cycles that pass a point per second, measured in hertz (Hz).

  • Relationship:

    • As frequency increases, energy increases.

    • As wavelength increases, energy decreases.

  • Key Equations:

    • Where is Planck's constant ( J·s) and is the speed of light ( m/s).

The Electromagnetic Spectrum

  • Electromagnetic Spectrum: The range of all types of electromagnetic radiation.

  • Visible Light: Wavelengths from about 400 nm (violet) to 700 nm (red).

  • Order of Regions (increasing wavelength): Gamma rays < X-rays < Ultraviolet < Visible < Infrared < Microwaves < Radio waves.

  • Relative Wavelengths: Gamma rays have the shortest, radio waves the longest.

Atomic Orbitals and Subshells

  • Orbitals: Regions in an atom where electrons are likely to be found.

  • Subshells: s, p, d, f (each with a specific number of orbitals):

    • s: 1 orbital

    • p: 3 orbitals

    • d: 5 orbitals

    • f: 7 orbitals

  • Shells (energy levels): Each shell contains n subshells (where n = principal quantum number).

  • Shapes: s (spherical), p (dumbbell), d (cloverleaf), f (complex).

Electron Configurations and Orbital Diagrams

  • Electron Configuration: The arrangement of electrons in an atom.

  • Example: For oxygen (O):

  • Orbital Diagram: Uses arrows to represent electrons in orbitals.

Periodic Trends

  • Atomic Size: Increases down a group, decreases across a period.

  • Ionization Energy: Energy required to remove an electron; decreases down a group, increases across a period.

Chapter 10: Chemical Bonding

Lewis Structures and Molecular Geometry

  • Lewis Structures: Diagrams showing valence electrons as dots around atoms.

  • Steps:

    1. Count total valence electrons.

    2. Arrange atoms and connect with single bonds.

    3. Distribute remaining electrons to satisfy octet rule.

  • Molecular Geometry: The 3D arrangement of atoms in a molecule (e.g., linear, bent, trigonal planar, tetrahedral).

  • Polarity: Determined by difference in electronegativity and molecular shape.

Bonding vs. Lone Pairs

  • Bonding Pairs: Electrons shared between atoms (form bonds).

  • Lone Pairs: Non-bonding electrons localized on a single atom.

Valence Electrons

  • Valence Electrons: Electrons in the outermost shell, involved in bonding.

  • Counting: For main group elements, equal to group number.

  • For ions: Add electrons for negative charge, subtract for positive charge.

Determining Geometry and Polarity

  • Electron Geometry: Arrangement of electron groups (bonding and lone pairs).

  • Molecular Geometry: Arrangement of atoms (ignoring lone pairs).

  • Polarity: If polar bonds are arranged asymmetrically, the molecule is polar.

Chapter 11: Gases

Units and Conversions

  • Pressure: 1 atm = 760 mmHg = 101.3 kPa

  • Volume: 1 L = 1000 mL

  • Temperature: K = °C + 273.15

Gas Laws

  • Boyle's Law: (at constant T, n)

  • Charles's Law: (at constant P, n)

  • Avogadro's Law: (at constant P, T)

  • Combined Gas Law:

  • Ideal Gas Law:

  • R (gas constant):

Stoichiometry with Gases

  • Use molar volume at STP (22.4 L/mol) or the ideal gas law to relate moles and volume.

  • Example: Calculate the volume of CO2 produced from 2.0 mol C at STP.

Chapter 12: Liquids, Solids, and Intermolecular Forces

Types of Intermolecular Forces (IMFs)

  • Dispersion (London) Forces: Present in all atoms and molecules; weakest IMF.

  • Dipole-Dipole Forces: Occur between polar molecules.

  • Hydrogen Bonds: Strong dipole-dipole interaction when H is bonded to N, O, or F.

IMFs and Physical Properties

  • Viscosity: Resistance to flow; increases with stronger IMFs.

  • Surface Tension: Energy required to increase surface area; increases with stronger IMFs.

  • Evaporation Rate: Decreases with stronger IMFs.

  • Vapor Pressure: Decreases with stronger IMFs.

  • Boiling Point: Increases with stronger IMFs.

Identifying IMFs and Miscibility

  • All molecules: Have dispersion forces.

  • Dipole-Dipole: Present if molecule is polar (asymmetrical shape, polar bonds).

  • Hydrogen Bonding: Present if H is bonded to N, O, or F.

  • Miscibility in Water: Substance must be polar or capable of hydrogen bonding.

  • Highest Vapor Pressure: Substance with weakest IMFs.

Chapter 13: Solutions

Electrolytes

  • Strong Electrolytes: Completely dissociate in water (e.g., NaCl).

  • Weak Electrolytes: Partially dissociate (e.g., acetic acid).

  • Non-Electrolytes: Do not dissociate (e.g., sugar).

Concentration Calculations

  • Mass Percent:

  • Molarity (M):

  • Dilution Equation:

Example Calculations

  • Mass Percent Example: If 5 g NaCl is dissolved in 95 g water, mass percent =

  • Molarity Example: 0.5 mol NaCl in 1.0 L solution:

  • Dilution Example: To make 100 mL of 0.2 M from 1.0 M stock:

Pearson Logo

스터디 프렙