A voltage V is applied to n identical resistors connected in parallel. If the resistors are instead all connected in series with the applied voltage, show that the power transformed is decreased by a factor n².

검증된 단계별 안내

Start by recalling the formula for power dissipated in a resistor: \( P = \frac{V^2}{R} \), where \( V \) is the voltage across the resistor and \( R \) is its resistance.

For the parallel configuration, the equivalent resistance \( R_{\text{eq,parallel}} \) of \( n \) identical resistors (each with resistance \( R \)) is given by \( \frac{1}{R_{\text{eq,parallel}}} = \frac{1}{R} + \frac{1}{R} + \dots + \frac{1}{R} = \frac{n}{R} \), so \( R_{\text{eq,parallel}} = \frac{R}{n} \). The power dissipated in this case is \( P_{\text{parallel}} = \frac{V^2}{R_{\text{eq,parallel}}} = \frac{V^2}{R/n} = n \frac{V^2}{R} \).

For the series configuration, the equivalent resistance \( R_{\text{eq,series}} \) of \( n \) identical resistors is \( R_{\text{eq,series}} = R + R + \dots + R = nR \). The power dissipated in this case is \( P_{\text{series}} = \frac{V^2}{R_{\text{eq,series}}} = \frac{V^2}{nR} \).

To find the factor by which the power is decreased, calculate the ratio \( \frac{P_{\text{series}}}{P_{\text{parallel}}} \). Substituting the expressions for \( P_{\text{series}} \) and \( P_{\text{parallel}} \), we get \( \frac{P_{\text{series}}}{P_{\text{parallel}}} = \frac{\frac{V^2}{nR}}{n \frac{V^2}{R}} = \frac{1}{n^2} \).

Thus, the power transformed in the series configuration is decreased by a factor of \( n^2 \) compared to the parallel configuration.

비슷한 문제에 대한 검증된 영상 답변:

이 영상 해법은 위 문제에 도움이 된다고 튜터들이 추천한 것입니다.

영상 길이:

도움이 되었나요?

주요 개념

질문에 올바르게 답하기 위해 반드시 이해해야 하는 핵심 개념들은 다음과 같습니다.

Ohm's Law

Ohm's Law states that the current (I) flowing through a conductor between two points is directly proportional to the voltage (V) across the two points and inversely proportional to the resistance (R) of the conductor. This relationship is expressed as V = IR, which is fundamental in analyzing electrical circuits, including those with resistors in series and parallel.

Power in Electrical Circuits

The power (P) consumed in an electrical circuit is defined as the rate at which energy is used or converted, calculated using the formula P = IV, where I is the current and V is the voltage. In resistive circuits, power can also be expressed as P = I²R or P = V²/R, depending on the configuration of the resistors, which is crucial for understanding how power changes with different connections.

Resistor Configurations: Series vs. Parallel

In a series configuration, resistors are connected end-to-end, resulting in a total resistance that is the sum of individual resistances (R_total = R1 + R2 + ... + Rn). In contrast, in a parallel configuration, the total resistance is reduced and calculated using the formula 1/R_total = 1/R1 + 1/R2 + ... + 1/Rn. This difference in resistance affects the current and power distribution in the circuit, leading to the conclusion that power is decreased by a factor of n² when switching from parallel to series.