Skip to main content
Ch 11: Equilibrium & Elasticity
Young & Freedman Calc - University Physics 14th Edition
Young & Freedman Calc14th EditionUniversity PhysicsISBN: 9780321973610당신이 사용하는 게 아니라요?교과서 변경
모든 교과서Young & Freedman Calc 14th EditionCh 11: Equilibrium & Elasticity문제 36
11장, 문제 36

A square steel plate is 10.0 cm on a side and 0.500 cm thick. (a) Find the shear strain that results if a force of magnitude 9.0×105 N is applied to each of the four sides, parallel to the side. (b) Find the displacement x (in centimeters).

검증된 단계별 안내
1
Understand the problem: We need to find the shear strain and the displacement of a square steel plate when a force is applied parallel to its sides.
Recall the formula for shear strain (γ), which is the ratio of the displacement (x) to the original length (L): γ = x / L.
Use the formula for shear stress (τ), which is the force (F) applied divided by the area (A) it is applied to: τ = F / A. Here, A is the area of one side of the square plate.
The shear modulus (G) relates shear stress and shear strain: τ = G * γ. Rearrange this to find the shear strain: γ = τ / G.
To find the displacement (x), use the relationship γ = x / L, where L is the side length of the plate. Rearrange to find x: x = γ * L.

비슷한 문제에 대한 검증된 영상 답변:

이 영상 해법은 위 문제에 도움이 된다고 튜터들이 추천한 것입니다.
영상 길이:
3m
도움이 되었나요?

주요 개념

질문에 올바르게 답하기 위해 반드시 이해해야 하는 핵심 개념들은 다음과 같습니다.

Shear Stress

Shear stress is the force per unit area acting parallel to the surface of a material. It is calculated by dividing the applied force by the area over which the force is distributed. In this problem, the shear stress is crucial for determining the shear strain, as it directly influences how the material deforms under the applied force.
추천 영상:
가이드 코스
07:49
Ray Diagrams for Convex Mirrors

Shear Strain

Shear strain is a measure of how much a material deforms in response to shear stress. It is defined as the displacement of a layer of the material divided by its original length. Understanding shear strain is essential for calculating the deformation of the steel plate when subjected to the given force, as it quantifies the angular distortion experienced by the material.

Shear Modulus

The shear modulus, also known as the modulus of rigidity, is a material property that describes its response to shear stress. It is the ratio of shear stress to shear strain and provides insight into the material's stiffness. For this problem, knowing the shear modulus of steel allows us to relate the applied force to the resulting shear strain and displacement, enabling the calculation of the plate's deformation.
추천 영상:
02:53
Example 1
관련 실천
교과서 질문

A solid gold bar is pulled up from the hold of the sunken RMS Titanic. The bulk modulus of lead is one-fourth that of gold. Find the ratio of the volume change of a solid lead bar to that of a gold bar of equal volume for the same pressure change.

1937
views
교과서 질문

A brass wire is to withstand a tensile force of 350 N without breaking. What minimum diameter must the wire have?

2475
views
교과서 질문

In the Challenger Deep of the Marianas Trench, the depth of seawater is 10.9 km and the pressure is 1.16×108 Pa (about 1.15×103 atm). If a cubic meter of water is taken from the surface to this depth, what is the change in its volume? (Normal atmospheric pressure is about 1.0×105 Pa. Assume that k for seawater is the same as the freshwater value given in Table 11.2.)

3273
views
교과서 질문

A specimen of oil having an initial volume of 600 cm3 is subjected to a pressure increase of 3.6×106 Pa, and the volume is found to decrease by 0.45 cm3. What is the bulk modulus of the material and the compressibility?

2909
views