Skip to main content
Ch 31: Alternating Current
Young & Freedman Calc - University Physics 14th Edition
Young & Freedman Calc14th EditionUniversity PhysicsISBN: 9780321973610당신이 사용하는 게 아니라요?교과서 변경
모든 교과서Young & Freedman Calc 14th EditionCh 31: Alternating Current문제 19a
31장, 문제 19a

The power of a certain CD player operating at 120 V rms is 20.0 W. Assuming that the CD player behaves like a pure resistor, find the maximum instantaneous power.

검증된 단계별 안내
1
Understand that the CD player is modeled as a pure resistor, which means it follows Ohm's Law. The power formula for a resistor is P = V^2 / R, where P is the power, V is the voltage, and R is the resistance.
Given that the CD player operates at 120 V rms and has a power of 20.0 W, use the formula P = V_rms^2 / R to find the resistance R. Rearrange the formula to R = V_rms^2 / P.
Calculate the resistance using the given values: R = (120 V)^2 / 20.0 W.
To find the maximum instantaneous power, recall that the maximum power in an AC circuit occurs at the peak voltage, which is V_peak = V_rms * sqrt(2).
Use the formula for instantaneous power P_max = V_peak^2 / R to find the maximum power. Substitute V_peak and the resistance R calculated earlier into this formula.

비슷한 문제에 대한 검증된 영상 답변:

이 영상 해법은 위 문제에 도움이 된다고 튜터들이 추천한 것입니다.
영상 길이:
2m
도움이 되었나요?

주요 개념

질문에 올바르게 답하기 위해 반드시 이해해야 하는 핵심 개념들은 다음과 같습니다.

RMS Voltage

RMS (Root Mean Square) voltage is a measure of the effective value of an alternating current (AC) voltage, equivalent to a DC voltage that delivers the same power. It is calculated as the square root of the average of the squares of the instantaneous values over one cycle. For a sinusoidal waveform, RMS voltage is 0.707 times the peak voltage.
추천 영상:
가이드 코스
07:14
RMS Current and Voltage

Power in Resistors

Power in resistors is calculated using the formula P = V^2/R, where P is the power, V is the voltage across the resistor, and R is the resistance. In AC circuits, the power can also be expressed using RMS values, as P = Vrms^2/R, which gives the average power consumed by the resistor over time.
추천 영상:
가이드 코스
06:00
Power

Instantaneous Power

Instantaneous power in an AC circuit is the power at any given moment, calculated as p(t) = v(t) * i(t), where v(t) is the instantaneous voltage and i(t) is the instantaneous current. For a pure resistor, the maximum instantaneous power occurs at the peak voltage and current, which is twice the average power calculated using RMS values.
추천 영상:
가이드 코스
06:00
Power
관련 실천
교과서 질문

In an L-R-C series circuit, the components have the following values: L = 20.0 mH, C = 140 nF, and R = 350 Ω.The generator has an rms voltage of 120 V and a frequency of 1.25 kHz. Determine (a) the power supplied by the generator and (b) the power dissipated in the resistor.

1884
views
교과서 질문

You have a 200-Ω resistor, a 0.400-H inductor, and a 6.00-μF capacitor. They are connected to form an L-R-C series circuit. What is the impedance of the circuit?

1818
views
교과서 질문

An L-R-C series circuit with L = 0.120 H, R = 240 Ω, and C = 7.30 μF carries an rms current of 0.450 A with a frequency of 400 Hz. What are the phase angle and power factor for this circuit?

1782
views
교과서 질문

An L-R-C series circuit is connected to a 120-Hz ac source that has Vrms = 80.0 V. The circuit has a resistance of 75.0 Ω and an impedance at this frequency of 105 Ω. What average power is delivered to the circuit by the source?

1791
views
교과서 질문

A resistor with R = 300 Ω and an inductor are connected in series across an ac source that has voltage amplitude 500 V. The rate at which electrical energy is dissipated in the resistor is 286 W. What is (a) the impedance Z of the circuit; (b) the amplitude of the voltage across the inductor; (c) the power factor?

2157
views
교과서 질문

You have a 200-Ω resistor, a 0.400-H inductor, and a 6.00-μF capacitor. They are connected to form an L-R-C series circuit. What is the current amplitude?

1696
views