Skip to main content
Back

Stoichiometry of Chemical Reactions: Study Notes

Study Guide - Smart Notes

Tailored notes based on your materials, expanded with key definitions, examples, and context.

Stoichiometry of Chemical Reactions

7.1 Writing and Balancing Chemical Equations

Chemical equations are symbolic representations of chemical reactions, showing the relationships between reactants and products. Balancing these equations is essential for quantitative chemical analysis and for obeying the law of conservation of mass.

  • Chemical Equation: Shows reactants and products, their physical states, and the relative quantities involved. For example:

  • Physical States: Indicated as (s) solid, (l) liquid, (g) gas, (aq) aqueous.

  • Subscripts vs. Coefficients: Subscripts indicate the number of atoms in a molecule; coefficients indicate the number of molecules or moles.

  • Law of Conservation of Mass: The total mass of reactants equals the total mass of products. Atoms must balance on both sides of the equation.

  • Balancing Equations: Adjust coefficients (not subscripts) to ensure the same number of each atom on both sides. Use the smallest whole-number coefficients.

  • Balancing with Fractions: If fractions are used, multiply all coefficients to obtain whole numbers.

  • Polyatomic Ions: Treat as intact units when they appear unchanged on both sides of the equation to simplify balancing.

Example:

Ionic Reactions and Aqueous Solutions

Many reactions occur in aqueous solutions, where water acts as a solvent. The behavior of substances in water depends on their ability to ionize.

  • Electrolytes:

    • Strong electrolytes: Completely ionize in water (e.g., NaCl).

    • Weak electrolytes: Partially ionize (e.g., acetic acid).

    • Nonelectrolytes: Do not ionize (e.g., sucrose).

  • Ionic Equations: Show all strong electrolytes as ions. There are three types:

    • Molecular equation: All species written as compounds.

    • Complete ionic equation: All strong electrolytes shown as ions.

    • Net ionic equation: Only species that undergo change are shown; spectator ions are omitted.

Example: Mixing and :

  • Molecular:

  • Complete ionic:

  • Net ionic: (or simplified: )

7.2 Classifying Chemical Reactions

Chemical reactions can be classified by the changes that occur and the products formed.

  • Precipitation Reactions: Formation of an insoluble solid (precipitate) when two solutions are mixed. Predicted using solubility rules.

  • Solubility Rules: Guidelines to predict whether a compound is soluble or insoluble in water.

  • Acids and Bases:

    • Acids: Produce in water. Strong acids dissociate completely; weak acids only partially.

    • Bases: Produce in water. Strong bases dissociate completely; weak bases only partially.

  • Acid–Base Neutralization: Acid reacts with base to form water and a salt. General form:

  • Redox Reactions: Involve transfer of electrons. Oxidation is loss of electrons; reduction is gain. Always occur together.

Example:

Oxidation Numbers

  • Definition: The charge an atom would have if electrons were transferred completely.

  • Rules:

    • Elemental form: 0

    • Monatomic ion: equals ion charge

    • Oxygen: usually -2 (except peroxides: -1)

    • Hydrogen: +1 (except metal hydrides: -1)

    • Halogens: usually -1 in ionic compounds

  • Sum of oxidation numbers: 0 for neutral compounds; equals ion charge for ions.

Example: Assign oxidation numbers in , , , , , .

7.3 Reaction Stoichiometry

Stoichiometry is the quantitative relationship between reactants and products in a chemical reaction, based on the balanced equation.

  • Mole Ratios: Derived from coefficients in the balanced equation. Used as conversion factors.

  • Calculations: Can convert between moles, mass, and number of molecules using molar mass and Avogadro's number.

Example: 1 mol produces 2 mol .

Stoichiometric Calculations

  • Mass–Mole–Mass Calculations: Convert mass to moles, use mole ratio, then convert back to mass if needed.

Example: What mass of is needed to produce 16 g of in the reaction ?

7.4 Reaction Yields

Not all reactions go to completion. The amount of product formed is determined by the limiting reactant, and the efficiency is measured by percent yield.

  • Limiting Reactant: The reactant that is completely consumed first, limiting the amount of product formed.

  • Theoretical Yield: Maximum amount of product possible, calculated from the limiting reactant.

  • Actual Yield: Amount of product actually obtained from the reaction.

  • Percent Yield:

Example: If 1.274 g of reacts with excess Zn to produce 0.392 g Cu, calculate the percent yield.

7.5 Quantitative Chemical Analysis

Analytical chemistry involves determining the identity and quantity of substances in a sample. Two common quantitative methods are gravimetric and volumetric analysis.

  • Gravimetric Analysis: Involves measuring mass changes, such as the mass of a precipitate or loss of water from a hydrate.

  • Volumetric Analysis (Titration): Involves measuring the volume of a solution of known concentration required to react with a solution of unknown concentration.

  • Indicator: A substance that changes color at (or near) the equivalence point to signal the end of the titration.

  • Equivalence Point: The point at which stoichiometrically equivalent quantities of reactants have reacted.

  • End Point: The point at which the indicator changes color, ideally very close to the equivalence point.

Example: A 50.00 mL sample of HCl requires 35.23 mL of 0.250 M NaOH for neutralization. Calculate the concentration of HCl.

Table: Common Solubility Rules (Summary)

Compound Type

Solubility

Exceptions

All nitrates (NO3-)

Soluble

None

All alkali metal salts (Li+, Na+, etc.)

Soluble

None

Chlorides, bromides, iodides

Soluble

Ag+, Pb2+, Hg22+

Sulfates (SO42-)

Soluble

Ba2+, Pb2+, Ca2+, Sr2+

Carbonates, phosphates

Insoluble

Alkali metals, NH4+

Hydroxides

Insoluble

Alkali metals, Ba2+, Sr2+

Additional info: For more detailed solubility rules, refer to a comprehensive chemistry textbook or handout.

Summary of Key Equations

  • Percent Yield:

  • Mole Calculations: (where n = moles, m = mass, M = molar mass)

  • Molarity: (where M = molarity, n = moles, V = volume in liters)

Pearson Logo

Study Prep