Skip to main content
Back

The Third Law of Thermodynamics and the Carnot Cycle: Entropy, Heat Engines, and Refrigerators

Study Guide - Smart Notes

Tailored notes based on your materials, expanded with key definitions, examples, and context.

The Third Law of Thermodynamics

Planck's Formulation and Absolute Entropy

The Third Law of Thermodynamics states that the entropy (S) of a pure, perfectly crystalline substance is zero at absolute zero temperature (0 K). This provides a real, natural zero for entropy, unlike enthalpy, which is defined relative to an arbitrary reference.

  • Entropy at 0 K: For a perfect crystal, there is only one microstate (W = 1), so .

  • Absolute Entropy: Because entropy has a real zero, absolute molar entropies can be tabulated and used directly in calculations.

  • Contrast with Enthalpy: Formation enthalpies are differences from an arbitrary zero, but entropy's zero is set by nature.

Example: Graphite, diamond, and C60 all have S = 0 at 0 K, despite their structural differences.

Calculating Absolute Entropy

Absolute entropy is determined by integrating the molar heat capacity over temperature, including phase transitions:

  • Integrate from 0 K to the temperature of interest.

  • Add entropy changes for each phase transition: .

  • Below the lowest measured temperature, extrapolate heat capacity as .

Formula:

Example: For O2, the calculated matches the accepted value.

Residual Entropy

Residual entropy occurs when a solid is not perfectly ordered at 0 K. For example, CO(s) molecules can freeze in two orientations, resulting in more than one microstate at 0 K.

  • Residual Entropy: where .

  • CO(s): Residual entropy is about , close to .

  • Third Law Zero: Only a perfect crystal achieves .

Standard States and Reaction Entropies

Standard Molar Entropy and Reaction Entropy

Standard molar entropies () are tabulated at 1 bar pressure. Unlike enthalpy, elements do not have zero entropy in their standard state.

  • Pressure Dependence:

  • Reaction Entropy: (sum over products minus reactants, each multiplied by its stoichiometric coefficient).

  • Rule of Thumb: is positive when the change in moles of gas () is positive, negative when .

Example: For the reaction :

  • Four moles of gas are consumed, none produced; the entropy change is large and negative.

Temperature Dependence of Reaction Entropy

Kirchhoff's Relation for Entropy

The temperature dependence of reaction entropy mirrors that of enthalpy, with a factor inside the integral:

  • If a phase change occurs in the interval, add for that transition.

Example: For :

  • At 298.15 K:

  • At 475 K:

  • Three moles of gas become one; the entropy change is strongly negative.

Heat Engines and the Carnot Cycle

Heat Engines and Efficiency

A heat engine absorbs heat from a hot reservoir, does work, and releases waste heat to a cold reservoir. The Carnot cycle is the most efficient reversible engine between two temperatures.

  • Carnot Cycle: Four segments: isothermal expansion (heat in), adiabatic expansion (cooling), isothermal compression (heat out), adiabatic compression (heating).

  • Efficiency:

  • Efficiency depends only on reservoir temperatures, not the working substance.

  • Real engines are less efficient due to irreversibility:

Key Equations:

Example: A reversible engine between 500 K and 200 K absorbing 1000 J from the hot reservoir has , so maximum work is 600 J; 400 J is dumped to the cold reservoir.

Second Law Statements

  • Kelvin–Planck Statement: No cyclic process can convert heat entirely into work.

  • Clausius Statement: No cyclic process can move heat from cold to hot without other effects.

  • Both are equivalent to and rule out perpetual motion machines.

Real-life Example: Power plants have limited efficiency; cogeneration can improve useful output by capturing waste heat.

Heat Pumps and Refrigerators

Operation and Coefficient of Performance

Running the Carnot cycle in reverse moves heat from cold to hot, requiring work input. Refrigerators and heat pumps transfer more heat than the work supplied.

  • Coefficient of Performance (COP): Measures performance, not efficiency.

  • Heat Pump:

  • Refrigerator:

  • COP values exceed 1; performance drops as the temperature gap increases.

Example: A heat pump between 294 K and 278 K has (ideal), but real units achieve only 2–3. A refrigerator at 255 K in a 294 K room has (ideal), but real units achieve about 1.5.

Real-life Example: Heat pumps can significantly reduce residential heating energy. Wind, solar, and hydro are not limited by Carnot efficiency.

Key Vocabulary

  • Third Law of Thermodynamics — States that the entropy of a perfect crystal approaches zero as its temperature approaches absolute zero.

  • Perfect crystal — A solid in which particles are arranged in a completely ordered structure with only one possible arrangement at absolute zero.

  • Absolute entropy — The total entropy of a substance measured relative to zero entropy at absolute zero for a perfect crystal.

  • Residual entropy — The entropy that remains in a substance at absolute zero because of disorder or multiple possible arrangements in its structure.

  • Standard state — The reference state of a substance under specified conditions, typically a pressure of 1 bar, used to measure and compare thermodynamic properties.

  • Standard reaction entropy — The entropy change of a chemical reaction when all reactants and products are in their standard states.

  • Heat engine — A device that absorbs heat from a hot reservoir, converts some of that energy into work, and releases the remaining heat to a cold reservoir.

  • Hot and cold reservoirs — Two systems at different temperatures that supply and absorb heat, respectively, during the operation of a heat engine.

  • Carnot cycle — An ideal reversible cycle consisting of two isothermal processes and two adiabatic processes that represents the maximum possible efficiency for a heat engine operating between two temperatures.

  • Reversible engine — An ideal heat engine that operates through reversible processes and can be reversed without leaving any net change in the system and its surroundings.

  • Efficiency — The fraction of heat absorbed by a heat engine that is converted into useful work.

  • Kelvin–Planck statement — States that no heat engine operating in a cycle can convert all the heat absorbed from a single reservoir completely into work without other effects.

  • Clausius statement — States that heat cannot spontaneously flow from a colder body to a hotter body without external work being supplied.

  • Perpetual motion machine of the second kind — A hypothetical device that continuously converts heat from a single reservoir entirely into work without producing any other effect, violating the Second Law of Thermodynamics.

  • Refrigerator — A device that uses external work to transfer heat from a cold reservoir to a hot reservoir.

  • Heat pump — A device that uses external work to transfer heat from a colder region to a warmer region for heating purposes.

  • Coefficient of performance — A measure of a refrigerator or heat pump's effectiveness, calculated as the desired heat transfer divided by the work input.

  • Cogeneration — The simultaneous production of useful electricity or mechanical work and heat from the same energy source.

Pearson Logo

Study Prep