Skip to main content
Ch 28: Fundamentals of Circuits
Knight Calc - Physics for Scientists and Engineers 5th Edition
Knight Calc5th EditionPhysics for Scientists and EngineersISBN: 9780137344796당신이 사용하는 게 아니라요?교과서 변경
모든 교과서Knight Calc 5th EditionCh 28: Fundamentals of Circuits문제 56b
28장, 문제 56b

A circuit you're building needs an ammeter that goes from 0 mA to a full-scale reading of 50 mA. Unfortunately, the only ammeter in the storeroom goes from 0 μA to a full-scale reading of only 500 μA. Fortunately, you've just finished a physics class, and you realize that you can make this ammeter work by putting a resistor in parallel with it, as shown in FIGURE P28.56. You've measured that the resistance of the ammeter is 50.0 Ω, not the 0 Ω of an ideal ammeter. What is the effective resistance of your ammeter?
Schematic showing a circuit with a 500 μA ammeter and a resistor labeled "R" in parallel, indicating current flow.

검증된 단계별 안내
1
Step 1: Understand the problem. The goal is to calculate the effective resistance of the modified ammeter circuit, which consists of the original ammeter (with resistance 50.0 Ω) in parallel with an additional resistor R. The effective resistance of the parallel combination will allow the ammeter to handle a full-scale current of 50 mA.
Step 2: Recall the formula for the equivalent resistance of two resistors in parallel. The formula is: Reff=11Rammeter+1R, where Rammeter is the resistance of the ammeter (50.0 Ω) and R is the resistance of the parallel resistor.
Step 3: Determine the current through the ammeter and the parallel resistor. The original ammeter can handle a maximum current of 500 μA, while the modified circuit needs to handle a full-scale current of 50 mA. The parallel resistor R must carry the remaining current, which is 50−0.5=49.5 mA.
Step 4: Use Ohm's Law to relate the voltage across the ammeter and the parallel resistor. The voltage across both components is the same because they are in parallel. Using Ohm's Law, V=IR, calculate the resistance R required to carry 49.5 mA while maintaining the same voltage as the ammeter.
Step 5: Substitute the values into the parallel resistance formula to find the effective resistance of the circuit. Once R is calculated, use the formula from Step 2 to compute Reff, which represents the effective resistance of the modified ammeter circuit.

비슷한 문제에 대한 검증된 영상 답변:

이 영상 해법은 위 문제에 도움이 된다고 튜터들이 추천한 것입니다.
도움이 되었나요?

주요 개념

질문에 올바르게 답하기 위해 반드시 이해해야 하는 핵심 개념들은 다음과 같습니다.

Ammeter Functionality

An ammeter is a device used to measure electric current in a circuit. It is connected in series with the circuit and ideally has zero resistance, allowing it to measure current without affecting the circuit. However, real ammeters have some internal resistance, which can influence the total current flowing through the circuit.
추천 영상:
가이드 코스
08:30
Intro to Wave Functions

Parallel Resistance

When resistors are connected in parallel, the total or effective resistance decreases. The formula for calculating the total resistance (R_total) of two resistors in parallel (R1 and R2) is given by 1/R_total = 1/R1 + 1/R2. This concept is crucial for modifying the ammeter's range by adding a resistor in parallel to achieve the desired current measurement.
추천 영상:
가이드 코스
12:42
Combining Resistors in Series & Parallel

Ohm's Law

Ohm's Law states that the current (I) flowing through a conductor between two points is directly proportional to the voltage (V) across the two points and inversely proportional to the resistance (R) of the conductor. It is expressed as V = I × R. Understanding this law is essential for analyzing circuits and calculating the effective resistance when modifying the ammeter's configuration.
추천 영상:
가이드 코스
03:07
Resistance and Ohm's Law
관련 실천
교과서 질문

What are the battery current Ibat and the potential difference V₁ - V₂ between points 1 and 2 when the switch in FIGURE P28.55 is (a) open and (b) closed?

170
views
교과서 질문

A 12 V car battery dies not so much because its voltage drops but because chemical reactions increase its internal resistance. A good battery connected with jumper cables can both start the engine and recharge the dead battery. Consider the automotive circuit of FIGURE P28.64. How much current is the dead battery alone able to drive through the starter motor?

1729
views
교과서 질문

A lightbulb is in series with a 2.0 Ω resistor. The lightbulb dissipates 10 W when this series circuit is connected to a 9.0 V battery. What is the current through the lightbulb? There are two possible answers; give both of them.

88
views
교과서 질문

What is the current through the 10 Ω resistor in FIGURE P28.61? Is the current from left to right or right to left?

232
views
교과서 질문

Load resistor R is attached to a battery of emf and internal resistance r. For what value of the resistance R, in terms of ∈ and r, will the power dissipated by the load resistor be a maximum?

572
views
교과서 질문

How much current flows through the bottom wire in FIGURE P28.66, and in which direction?

204
views